Are you using an Edelbrock Performer or Thunder series AVS carburetor? Then you need these Edelbrock metering jets! The jet and rod is changed to get the cruise air/ fuel ratio leaned out. The step in the rod changes the effective jet area between high and low manifold vacuum conditions. The brass metering jets are designed for use with Edelbrock Performer series and Thunder series AVS carburetors only. Do not use them with any other brands.
Ihre Daten sind bei uns sicher und werden nicht an Dritte weitergegeben¨
Lieferungen gemäss den allgemeinen Geschäftsbedingungen
Umtausch gemäss den allgemeinen Geschäftsbedingung
- Set of 2.
- Thread size: 5/16``-24.
Edelbrock fuel pump block-off plates are designed to block-off the stock fuel pump mounting location when a mechanical fuel pump is replaced with an electrical system.
Edelbrock single and dual regulator kits are designed for use with Holley square bore or 4500 Dominator series dual-feed carburetors on alcohol, turbo and supercharged gasoline engines. They will allow you to adjust fuel pressure from 4-1/2 to 9 PSI and are recommended for use with either Edelbrock racing fuel pumps or any high-output fuel pumps. The kits...
These Edelbrock carburetor spacers allow you to space your carburetor above the intake flange to increase plenum area for more torque and horsepower. Available in aluminum and heat-insulating phenolic or wood fiber, these Edelbrock carb spacers are just what you need to insulate or tune your carburetor/manifold powerband.
Edelbrock has paved the way to a trouble-free manifold installation job for you with this comprehensive array of accessories. These accessories include anodized air cleaner hold nuts, manifold pipe plugs, and everything in between.
Edelbrock throttle cable brackets are just what you need to hook up your cables the right way.
This billet aluminum street fuel filter is made of billet aluminum for strength and shock resistance. Designed for carbureted engines making less than 300 HP, this bi-directional filter features a sintered bronze 40-micron element that can be cleaned or replaced.
Mr. Gasket air cleaner spacers will properly locate your air cleaner, solving any interference problems you might have.
Mr. Gasket medium length carburetor studs put an end to stripped-out threads in cast aluminum manifolds, holding the gasket in place and perfectly aligning the carburetor in position. Zinc-plated and 1-3/8-inch long, they have 5/16-18 threads on one end and 5/16-24 on the other, come in a package of four, and have four matching nuts and washers to...
Edelbrock metering rods are specifically designed for use with Edelbrock Performer series carburetors. Do not attempt to use them with other brands. A variety of sizes is available.
These Mr. Gasket air cleaners will dress-up your engine compartment for that show car look. When it comes to good looks and durability, Mr. Gasket has you covered.
Tune any Q-Jet with Edelbrock secondary metering rods. These secondary metering rods will work on any year Quadrajet. The dimension indicates the tip diameter, not the shaft diameter.
Edelbrock has paved the way to a trouble-free manifold installation job for you with this comprehensive array of accessories. These accessories include anodized air cleaner hold nuts, manifold pipe plugs, and everything in between.
The Performer carburetor maintenance kits consist of genuine Edelbrock parts that will help you to keep your carburetor in top notch condition. These kits include all of the parts and gaskets necessary to rebuild or modify your Edelbrock Performer carb.
Edelbrock carburetor gasket kits are made to signify the high standards and performance that Edelbrock is known for. Edelbrock gasket kits seal intakes, heads, carb-to-manifolds and other components. You can trust the quality of Edelbrock carburetor gasket kits to protect your engine.
Edelbrock Pro-Flo Series air cleaners are the perfect solution to your low hood clearance problems. These high-quality air cleaners are available in several styles and sizes to suit your tastes and fit your ride.
Edelbrock metering rods are specifically designed for use with Edelbrock Performer series carburetors. Do not attempt to use them with other brands. A variety of sizes is available.
Are you using an Edelbrock Performer or Thunder series AVS carburetor? Then you need these Edelbrock metering jets! The jet and rod is changed to get the cruise air/ fuel ratio leaned out. The step in the rod changes the effective jet area between high and low manifold vacuum conditions. The brass metering jets are designed for use with Edelbrock Performer series and Thunder series AVS carburetors only. Do not use them with any other brands.
