Mr. Gasket medium length carburetor studs put an end to stripped-out threads in cast aluminum manifolds, holding the gasket in place and perfectly aligning the carburetor in position. Zinc-plated and 2-inch long, they have 5/16-18 threads on one end and 5/16-24 on the other, come in a package of four, and have four matching nuts and washers to complete the job.
Security policy (edit with Customer reassurance module)
Delivery policy (edit with Customer reassurance module)
Return policy (edit with Customer reassurance module)
- Puts an end to stripped out threads in cast aluminum manifolds.
- Holds the gasket in place and perfectly aligns the carburetor in position.
- Zinc plated and 2 inch long with 5/16 coarse threads on one end an 5/16 find threads on the other.
- Package of four with four matching nuts and washers.
Edelbrock metering rods are specifically designed for use with Edelbrock Performer series carburetors. Do not attempt to use them with other brands. A variety of sizes is available.
The Performer carburetor maintenance kits consist of genuine Edelbrock parts that will help you to keep your carburetor in top notch condition. These kits include all of the parts and gaskets necessary to rebuild or modify your Edelbrock Performer carb.
Edelbrock metering rods are specifically designed for use with Edelbrock Performer series carburetors. Do not attempt to use them with other brands. A variety of sizes is available.
This carburetor bushing kit reduces the ½`` throttle shaft hole to ¼`` I.D., which makes for easy throttle linkage attachment, or can be used to replace the stock rubber unit. Machined from cold roll steel, then bright zinc plated, the two piece bushing measures 9/16`` wide when installed and fits most 4-bbl. carburetors with ½`` throttle linkage hole....
These Edelbrock carburetor spacers allow you to space your carburetor above the intake flange to increase plenum area for more torque and horsepower. Available in aluminum and heat-insulating phenolic or wood fiber, these Edelbrock carb spacers are just what you need to insulate or tune your carburetor/manifold powerband.
36`` long cable wrapped with a 24`` stainless steel braided sleeve. Can be cut to length to fit your specific application.
Mr. Gasket Flat Black Easy-Flow Air Cleaners customize your engine compartment for that stealth look. Designed to fit all single 2-, 3-, and 4-barrel carburetors with 5.125-inch carburetor necks, these competition air cleaners are ideal for either race or high-performance street use.
These Mr. Gasket air cleaners will dress-up your engine compartment for that show car look. When it comes to good looks and durability, Mr. Gasket has you covered.
Edelbrock throttle cable brackets are just what you need to hook up your cables the right way.
Edelbrock metering rods are specifically designed for use with Edelbrock Performer series carburetors. Do not attempt to use them with other brands. A variety of sizes is available.
These Mr. Gasket air cleaner adapters end air cleaner fitment problems when you change carburetors. Molded from high-impact, heat-resistant material for durability.
Edelbrock Performer EPS intake manifold and carburetor kits contain all of the necessary pieces to upgrade your induction system. They include an Edelbrock Performer EPS aluminum intake manifold with either a natural aluminum finish or an EnduraShine finish, an intake gasket set, intake manifold bolts, a carburetor stud kit, and a Performer Series 600 CFM...
Are you using an Edelbrock Performer or Thunder series AVS carburetor? Then you need these Edelbrock metering jets! The jet and rod is changed to get the cruise air/ fuel ratio leaned out. The step in the rod changes the effective jet area between high and low manifold vacuum conditions. The brass metering jets are designed for use with Edelbrock...
These direct replacement floats are made from a high quality phenolic resin and will fit a variety of Edelbrock and GM carbs.
Edelbrock throttle cable brackets are just what you need to hook up your cables the right way.
Increase your power and performance with this 1`` carburetor spacer from Mr.Gasket. Designed to fit the standard Holley & Carter bolt pattern. This precision die cast aluminum spacer kit includes the studs, washers, nuts, gaskets and 3/8`` PCV tube.
Mr. Gasket medium length carburetor studs put an end to stripped-out threads in cast aluminum manifolds, holding the gasket in place and perfectly aligning the carburetor in position. Zinc-plated and 2-inch long, they have 5/16-18 threads on one end and 5/16-24 on the other, come in a package of four, and have four matching nuts and washers to complete the job.
