Mr. Gasket medium length carburetor studs put an end to stripped-out threads in cast aluminum manifolds, holding the gasket in place and perfectly aligning the carburetor in position. Zinc-plated and 2-inch long, they have 5/16-18 threads on one end and 5/16-24 on the other, come in a package of four, and have four matching nuts and washers to complete the job.
Ihre Daten sind bei uns sicher und werden nicht an Dritte weitergegeben¨
Lieferungen gemäss den allgemeinen Geschäftsbedingungen
Umtausch gemäss den allgemeinen Geschäftsbedingung
- Puts an end to stripped out threads in cast aluminum manifolds.
- Holds the gasket in place and perfectly aligns the carburetor in position.
- Zinc plated and 2 inch long with 5/16 coarse threads on one end an 5/16 find threads on the other.
- Package of four with four matching nuts and washers.
The 5-3/4" long stud fits air Filters up to 5" tall. The 1/4"-20 stud fits most carburetors. Dominator carburetors use the adapter since they have a 5/16"-18 tapped hole in the carburetor.
Edelbrock knows carbs. That`s why they offer these calibration kits for Performers series carburetors. They include all the parts you need to help you get the best performance from Edelbrock carburetors.
Are you using an Edelbrock Performer or Thunder series AVS carburetor? Then you need these Edelbrock metering jets! The jet and rod is changed to get the cruise air/ fuel ratio leaned out. The step in the rod changes the effective jet area between high and low manifold vacuum conditions. The brass metering jets are designed for use with Edelbrock...
Edelbrock fuel pump block-off plates are designed to block-off the stock fuel pump mounting location when a mechanical fuel pump is replaced with an electrical system.
Edelbrock Pro-Flo universal conical air filter elements are an economical way to ensure that your engine is getting clean air - without the expense of buying a new filter every few thousand miles. They`re constructed for superior filtration and airflow performance. The filter elements feature triple chrome plated trim for a show-quality look and are...
Mr. Gasket air cleaner spacers will properly locate your air cleaner, solving any interference problems you might have.
Mr. Gasket air cleaner nuts are a perfect chrome-plated custom accessory for engine appearance. These spin nuts enhance any air cleaner.
Thanks to the folks at Edelbrock, installing your new intake and carburetor has been made easier. With their EGR adapters, your existing EGR valve is repositioned to allow clearance for your carburetor. They`re made of cast aluminum and come complete with gaskets and bolts.
Edelbrock metering rods are specifically designed for use with Edelbrock Performer series carburetors. Do not attempt to use them with other brands. A variety of sizes is available.
Edelbrock throttle cable brackets are just what you need to hook up your cables the right way.
These Mr. Gasket air cleaner adapters end air cleaner fitment problems when you change carburetors. Molded from high-impact, heat-resistant material for durability.
Edelbrock Q-Jet bolt kits are suited for all Quadrajets, except for model EDL-1905. They include all of the bolts and hardware needed to mount your Performer Quadrajet to your intake manifold.
This high quality filter is a must when your old filter becomes dirty and doesn't look fresh. This filter is white paper and brings out the bling in that engine compartment and also keeps that air coming. Clogged up dirty air filters will hurt performance and cause your engine to run poorly.
Edelbrock has paved the way to a trouble-free manifold installation job for you with this comprehensive array of accessories. These accessories include anodized air cleaner hold nuts, manifold pipe plugs, and everything in between.
Rebuilding your nostalgic 94 carburetor? Edelbrock 94 rebuild kits contain everything you need to do the job right. Kits include fuel inlet seat and needle, accelerator pump assembly and spring, accelerator check ball, check ball retainer, power valve assembly, float gauge and all the necessary gaskets. These rebuild kits will overhaul any Edelbrock 94 or...
Mr. Gasket medium length carburetor studs put an end to stripped-out threads in cast aluminum manifolds, holding the gasket in place and perfectly aligning the carburetor in position. Zinc-plated and 1.5-inch long, they have 5/16-18 threads on one end and 5/16-24 on the other, come in a package of four, and have four matching nuts and washers to complete...
Mr. Gasket medium length carburetor studs put an end to stripped-out threads in cast aluminum manifolds, holding the gasket in place and perfectly aligning the carburetor in position. Zinc-plated and 2-inch long, they have 5/16-18 threads on one end and 5/16-24 on the other, come in a package of four, and have four matching nuts and washers to complete the job.
