Mr. Gasket air cleaner nuts are a perfect chrome-plated custom accessory for engine appearance. These spin nuts enhance any air cleaner.
Ihre Daten sind bei uns sicher und werden nicht an Dritte weitergegeben¨
Lieferungen gemäss den allgemeinen Geschäftsbedingungen
Umtausch gemäss den allgemeinen Geschäftsbedingung
- Chrome and black.
- Fits ¼``-20 & 5/16``-18 threads.
Special heat-absorbing material with layers of aluminum alloy forces heat away from the carburetor. Allows a cooler, denser fuel mixture to prevent engine heat from vapor-locking gasoline in the carburetor.
Mr. Gasket air cleaner spacers will properly locate your air cleaner, solving any interference problems you might have.
You want the best bolts for your buck? Then use Mr. Gasket`s zinc plated grade 5 steel hex head intake manifold bolts 3/8``-16 x 1``. Includes flat washers to provide a uniform clamp load and to help prevent galling on aluminum manifolds.
Edelbrock metering rods are specifically designed for use with Edelbrock Performer series carburetors. Do not attempt to use them with other brands. A variety of sizes is available.
Install your throttle cables the right way with these throttle return kits from Edelbrock. Each kit includes the springs and bracket you need to ensure good looks and proper throttle actuation.
Edelbrock carburetor stud kits supply all of the correct studs, nuts and washers to mount your Edelbrock carburetor correctly. These carb stud kits are must-have accessories when installing or tuning your carburetor.
This block-off plate is cut to cover stock fuel pump openings. Gasket included. Chevrolet 265 thru 400 cui.
Are you using an Edelbrock Performer or Thunder series AVS carburetor? Then you need these Edelbrock metering jets! The jet and rod is changed to get the cruise air/ fuel ratio leaned out. The step in the rod changes the effective jet area between high and low manifold vacuum conditions. The brass metering jets are designed for use with Edelbrock...
These Mr. Gasket air cleaners will dress-up your engine compartment for that show car look. When it comes to good looks and durability, Mr. Gasket has you covered.
This carburetor bushing kit reduces the ½`` throttle shaft hole to ¼`` I.D., which makes for easy throttle linkage attachment, or can be used to replace the stock rubber unit. Machined from cold roll steel, then bright zinc plated, the two piece bushing measures 9/16`` wide when installed and fits most 4-bbl. carburetors with ½`` throttle linkage hole....
Edelbrock offers these divorced choke rods specifically for use with Q-Jet carbs and Edelbrock manifolds. They are quality pieces for direct replacement of the choke rods on your Q-Jet.
Edelbrock single and dual regulator kits are designed for use with Holley square bore or 4500 Dominator series dual-feed carburetors on alcohol, turbo and supercharged gasoline engines. They will allow you to adjust fuel pressure from 4-1/2 to 9 PSI and are recommended for use with either Edelbrock racing fuel pumps or any high-output fuel pumps. The kits...
These Edelbrock carburetor spacers allow you to space your carburetor above the intake flange to increase plenum area for more torque and horsepower. Available in aluminum and heat-insulating phenolic or wood fiber, these Edelbrock carb spacers are just what you need to insulate or tune your carburetor/manifold powerband.
Edelbrock knows carbs. That`s why they offer these calibration kits for Performers series carburetors. They include all the parts you need to help you get the best performance from Edelbrock carburetors.
This high performance electric fuel pump has a free flow rate of 105 GPH with a maximum pressure of 14 psi.
Edelbrock air cleaner spacers are designed to fit between your carburetor neck flange and the air filter assembly. They come in different heights to allow for the right amount of clearance you need for your application.
Mr. Gasket air cleaner nuts are a perfect chrome-plated custom accessory for engine appearance. These spin nuts enhance any air cleaner.
