Edelbrock`s Performer carburetors feature two-piece, all-aluminum construction for cooler operating temperatures and less warping. There are no gaskets below the fuel bowl level for fewer leaks, and no plastic parts or power valves to blow out. The carbs use easily changed metering rods for precise tuning, non-adjustable secondary air valves and the primary venturi booster is a bottom-feed design for smoother acceleration and better driveability. Also included with every Edelbrock carburetor you will receive an owner`s manual. These manuals consist of two sections: Section 1, theory of operation and tuning procedures which will help you be prepared to develop your own individualized calibration. Section 2, tuning procedures will take you through a step-by-step procedure that will enable you to achieve a desirable calibration. For added ease of tuning, a Calibration reference chart for your model of carburetor will be included.
Ihre Daten sind bei uns sicher und werden nicht an Dritte weitergegeben¨
Lieferungen gemäss den allgemeinen Geschäftsbedingungen
Umtausch gemäss den allgemeinen Geschäftsbedingung
- CFM: 600.
- Number of barrels: 4.
- Carburetor flange: Square bore.
- Choke: Electric.
- Secondary type: Mechanical.
- Fuel inlet: Single.
- Carburetor finish: Silver.
The Mr.Gasket carburetor heat shield will help eliminate fuel boiling and vapor lock caused by heat conducted from the manifold to the carburetor.
Edelbrock throttle lever adapters are designed to facilitate an easy connection of your factory cable-operated linkages to your new Edelbrock Performer carburetor.
Clean fuel equals better performance and Edlbrock inline fuel filters will help. They offer a variety of filters that will keep your go-juice from being contaminated. Edelbrock inline fuel filters screen out the bad stuff so your engine gets the good stuff.
This lightweight pump includes mounting bracket and hardware and is universal for all carbureted gasoline engines. 7 PSI max. 95 GPH.
These Edelbrock Vacuum Caps provide a way to seal vacuum line connections on your intake manifold, carburetor or wherever you need.
Thanks to the folks at Edelbrock, installing your new intake and carburetor has been made easier. With their EGR adapters, your existing EGR valve is repositioned to allow clearance for your carburetor. They`re made of cast aluminum and come complete with gaskets and bolts.
Edelbrock Victor Series air cleaners feature a die-cast aluminum lid that is black powdercoated with a finely textured surface for a pleasing and unique appearance. This is the same finish that you`ll find on Edelbrock`s other new Victor Series accessories. These air cleaners will work with all popular 5 1/8 in. carburetors or 4-barrel throttle bodies and...
These Grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds.
This bell crank kit features 12 mounting holes for multi-arm positioning and can be used in either push or pull type throttle linkages. Center hole is ¼`` diameter for easy mounting. Each arm has 3 holes for various throttle ratios. Kit includes all hardware needed for installation along with universal throttle bracket.
Edelbrock carburetor gasket kits are made to signify the high standards and performance that Edelbrock is known for. Edelbrock gasket kits seal intakes, heads, carb-to-manifolds and other components. You can trust the quality of Edelbrock carburetor gasket kits to protect your engine.
Edelbrock knows carbs. That`s why they offer these calibration kits for Performers series carburetors. They include all the parts you need to help you get the best performance from Edelbrock carburetors.
Mr. Gasket air cleaner spacers will properly locate your air cleaner, solving any interference problems you might have.
Are you using an Edelbrock Performer or Thunder series AVS carburetor? Then you need these Edelbrock metering jets! The jet and rod is changed to get the cruise air/ fuel ratio leaned out. The step in the rod changes the effective jet area between high and low manifold vacuum conditions. The brass metering jets are designed for use with Edelbrock...
These Edelbrock throttle lever studs are designed to hook cables up to your carburetor. They come in a variety of styles for throttle cables, cruise control cables and transmission kickdown cables.
Edelbrock Pro-Flo Series air cleaners are the perfect solution to your low hood clearance problems. These high-quality air cleaners are available in several styles and sizes to suit your tastes and fit your ride.
Edelbrock air cleaner spacers are designed to fit between your carburetor neck flange and the air filter assembly. They come in different heights to allow for the right amount of clearance you need for your application.
Edelbrock`s Performer carburetors feature two-piece, all-aluminum construction for cooler operating temperatures and less warping. There are no gaskets below the fuel bowl level for fewer leaks, and no plastic parts or power valves to blow out. The carbs use easily changed metering rods for precise tuning, non-adjustable secondary air valves and the primary venturi booster is a bottom-feed design for smoother acceleration and better driveability. Also included with every Edelbrock carburetor you will receive an owner`s manual. These manuals consist of two sections: Section 1, theory of operation and tuning procedures which will help you be prepared to develop your own individualized calibration. Section 2, tuning procedures will take you through a step-by-step procedure that will enable you to achieve a desirable calibration. For added ease of tuning, a Calibration reference chart for your model of carburetor will be included.
