You want the best bolts for your buck? Then use Mr. Gasket`s zinc plated grade 5 steel hex head intake manifold bolts 3/8``-16 x 1``. Includes flat washers to provide a uniform clamp load and to help prevent galling on aluminum manifolds.
Security policy (edit with Customer reassurance module)
Delivery policy (edit with Customer reassurance module)
Return policy (edit with Customer reassurance module)
- 3/8``-16 x 1``.
- 12 bolts with washers.
- Fits Chevy Small Block 1955-1995 265-400.
- Fits Chrysler Small Block 1964-1986 273-360.
- Fits Chrysler Big Block 1959-1980 361-440 Wedge Engines.
- Fits AMC 290-401.
Use to block off open engine vacuum fittings. Sixteen pcs. Of "Buna-N" rubber offer more durability, longer life than neoprene/vinyl, especially when exposed to high temps.
These are high quality gaskets that are a good choice for replacement to seal those annoying leaks or when doing jet changes at the track.
Edelbrock carburetor stud kits supply all of the correct studs, nuts and washers to mount your Edelbrock carburetor correctly. These carb stud kits are must-have accessories when installing or tuning your carburetor.
These Mr. Gasket air cleaner adapters end air cleaner fitment problems when you change carburetors. Molded from high-impact, heat-resistant material for durability.
This high quality filter is a must when your old filter becomes dirty and doesn't look fresh. This filter is white paper and brings out the bling in that engine compartment and also keeps that air coming. Dirty filters will hurt performance and cause your engine to run a rich mixture.
Edelbrock throttle cable brackets are just what you need to hook up your cables the right way.
Edelbrock knows carbs. That`s why they offer these calibration kits for Performers series carburetors. They include all the parts you need to help you get the best performance from Edelbrock carburetors.
Edelbrock has paved the way to a trouble-free manifold installation job for you with this comprehensive array of accessories. These accessories include anodized air cleaner hold nuts, manifold pipe plugs, and everything in between.
Edelbrock Pro-Flo Series air cleaners are the perfect solution to your low hood clearance problems. These high-quality air cleaners are available in several styles and sizes to suit your tastes and fit your ride.
Edelbrock fuel pressure regulators are machined from aircraft-quality aluminum for those who demand the best. These regulators feature fluorosilicone diaphragm material for extended life and high-temperature protection. They are compatible with all grades of gasoline/methanol.
Edelbrock metering rods are specifically designed for use with Edelbrock Performer series carburetors. Do not attempt to use them with other brands. A variety of sizes is available.
Are you using an Edelbrock Performer or Thunder series AVS carburetor? Then you need these Edelbrock metering jets! The jet and rod is changed to get the cruise air/ fuel ratio leaned out. The step in the rod changes the effective jet area between high and low manifold vacuum conditions. The brass metering jets are designed for use with Edelbrock...
Rebuilding your nostalgic 94 carburetor? Edelbrock 94 rebuild kits contain everything you need to do the job right. Kits include fuel inlet seat and needle, accelerator pump assembly and spring, accelerator check ball, check ball retainer, power valve assembly, float gauge and all the necessary gaskets. These rebuild kits will overhaul any Edelbrock 94 or...
These Edelbrock carburetor spacers allow you to space your carburetor above the intake flange to increase plenum area for more torque and horsepower. Available in aluminum and heat-insulating phenolic or wood fiber, these Edelbrock carb spacers are just what you need to insulate or tune your carburetor/manifold powerband.
This block-off plate is cut to cover stock fuel pump openings. Gasket included. Chevrolet 265 thru 400 cui.
These Edelbrock carburetor idle mixture screws will fit directly into the base plate of your Edelbrock carburetor. They will allow adjustment to the idle circuit inside of the carburetor base plate. The screws are made of steel and include new springs for a simple installation.
You want the best bolts for your buck? Then use Mr. Gasket`s zinc plated grade 5 steel hex head intake manifold bolts 3/8``-16 x 1``. Includes flat washers to provide a uniform clamp load and to help prevent galling on aluminum manifolds.
