Special heat-absorbing material with layers of aluminum alloy forces heat away from the carburetor. Allows a cooler, denser fuel mixture to prevent engine heat from vapor-locking gasoline in the carburetor. This unit also acts as a carburetor mounting gasket.
Ihre Daten sind bei uns sicher und werden nicht an Dritte weitergegeben¨
Lieferungen gemäss den allgemeinen Geschäftsbedingungen
Umtausch gemäss den allgemeinen Geschäftsbedingung
- This carburetor heat dissipator fits Holley & AFB and is ¼`` thick.
- 4 hole design with 1-11/16`` diameter for each hole.
- Each gasket & aluminum plate is 1/16`` thick.
Get smooth trouble-free throttle operation with a new bushing. Fits 1/4" diameter rod.
Edelbrock throttle cable brackets are designed to be used with EDL-1483 or EDL-1844 throttle level adapters to reposition your factory throttle cable to align with Edelbrock Performer or Thunder Series carburetors. Designed for Ford products with cable operated throttle and automatic kick down rod. The throttle cable plate kit only works when the throttle...
This high performance electric fuel pump has a free flow rate of 105 GPH with a maximum pressure of 14 psi.
Mr. Gasket`s MICRO ELECTRIC Diesel FUEL PUMP, 12-volt electric transfer pump is safe for diesel fuel use. Simple 2 wire design, gravity fed type pump, includes 100 micron in line filter. 4-7 PSI, 35GPH, small universal design allows easy set and installation anywhere.
Edelbrock metering rods are specifically designed for use with Edelbrock Performer series carburetors. Do not attempt to use them with other brands. A variety of sizes is available.
This carburetor bushing kit reduces the ½`` throttle shaft hole to ¼`` I.D., which makes for easy throttle linkage attachment, or can be used to replace the stock rubber unit. Machined from cold roll steel, then bright zinc plated, the two piece bushing measures 9/16`` wide when installed and fits most 4-bbl. carburetors with ½`` throttle linkage hole....
Edelbrock metering rods are specifically designed for use with Edelbrock Performer series carburetors. Do not attempt to use them with other brands. A variety of sizes is available.
Edelbrock throttle cable brackets are designed to be used with EDL-1483 or EDL-1844 throttle level adapters to reposition your factory throttle cable to align with Edelbrock Performer or Thunder Series carburetors. Designed for Ford products with cable operated throttle and automatic kick down rod. The throttle cable plate kit only works when the throttle...
These highly polished, aluminum velocity stacks increase carburetor intake speed and capacity to maximize horsepower. Fits Holley carbs with 5-1/8``neck.
These Grade 5 hex head bolts are zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds.
Edelbrock knows carbs. That`s why they offer these calibration kits for Performers series carburetors. They include all the parts you need to help you get the best performance from Edelbrock carburetors.
This high quality filter is a must when your old filter becomes dirty and doesn't look fresh. This filter is white paper and brings out the bling in that engine compartment and also keeps that air coming. Clogged up dirty air filters will hurt performance and cause your engine to run poorly.
Edelbrock metering rods are specifically designed for use with Edelbrock Performer series carburetors. Do not attempt to use them with other brands. A variety of sizes is available.
The Performer carburetor maintenance kits consist of genuine Edelbrock parts that will help you to keep your carburetor in top notch condition. These kits include all of the parts and gaskets necessary to rebuild or modify your Edelbrock Performer carb.
Fits Holley carburetors, includes non-stick washer.
Hold your air cleaner down with style! Edelbrock air cleaner wing nuts are just what you need to top-off that new air cleaner assembly. They are designed from high quality materials and will give your air filter the extra touch for a great look.
Special heat-absorbing material with layers of aluminum alloy forces heat away from the carburetor. Allows a cooler, denser fuel mixture to prevent engine heat from vapor-locking gasoline in the carburetor. This unit also acts as a carburetor mounting gasket.
