MR. GASKET Chevy Intake Manifold Bolt Kit 3/8-16x1''
These Grade 5 hex head bolts are zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds.
Edelbrock fuel pressure regulators are machined from aircraft-quality aluminum for those who demand the best. These regulators feature fluorosilicone diaphragm material for extended life and high-temperature protection. They are compatible with all grades of gasoline/methanol.
Ihre Daten sind bei uns sicher und werden nicht an Dritte weitergegeben¨
Lieferungen gemäss den allgemeinen Geschäftsbedingungen
Umtausch gemäss den allgemeinen Geschäftsbedingung
These Grade 5 hex head bolts are zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds.
Edelbrock Thunder Series AVS carburetor calibration kits are designed to tune your car to match any engine or track condition. These kits include an assortment of metering rods and jets, a pair of metering rod retaining springs, and a complete assortment of step-up springs.
You want the best bolts for your buck? Then use Mr. Gasket`s zinc plated grade 5 steel hex head intake manifold bolts 3/8``-16 x 1``. Includes flat washers to provide a uniform clamp load and to help prevent galling on aluminum manifolds.
Carburetor adapters from Edelbrock allow you to use almost any carburetor on almost any intake. They will save you the hassle and expense of purchasing all-new components when changing carburetors or intakes.
These Edelbrock fuel pressure regulator brackets are designed to mount your regulator right by the carburetor. They are made from aluminum for durability.
These Mr. Gasket air cleaners will dress-up your engine compartment for that show car look. When it comes to good looks and durability, Mr. Gasket has you covered.
These Edelbrock carburetor spacers allow you to space your carburetor above the intake flange to increase plenum area for more torque and horsepower. Available in aluminum and heat-insulating phenolic or wood fiber, these Edelbrock carb spacers are just what you need to insulate or tune your carburetor/manifold powerband.
Mr. Gasket air cleaner spacers will properly locate your air cleaner, solving any interference problems you might have.
Edelbrock carburetor gasket kits are made to signify the high standards and performance that Edelbrock is known for. Edelbrock gasket kits seal intakes, heads, carb-to-manifolds and other components. You can trust the quality of Edelbrock carburetor gasket kits to protect your engine.
This high quality filter is a must when your old filter becomes dirty and doesn't look fresh. This filter is white paper and brings out the bling in that engine compartment. Dirty filters will hurt performance and cause your engine to run poorly.
Edelbrock metering rods are specifically designed for use with Edelbrock Performer series carburetors. Do not attempt to use them with other brands. A variety of sizes is available.
Are you using an Edelbrock Performer or Thunder series AVS carburetor? Then you need these Edelbrock metering jets! The jet and rod is changed to get the cruise air/ fuel ratio leaned out. The step in the rod changes the effective jet area between high and low manifold vacuum conditions. The brass metering jets are designed for use with Edelbrock...
Are you using an Edelbrock Performer or Thunder series AVS carburetor? Then you need these Edelbrock metering jets! The jet and rod is changed to get the cruise air/ fuel ratio leaned out. The step in the rod changes the effective jet area between high and low manifold vacuum conditions. The brass metering jets are designed for use with Edelbrock...
When doing a rebuild on your Edelbrock carburetor, don`t forget to replace your accelerator pump with one of these top quality replacement pump assemblies. The right components will help to keep your carb working to its full potential.
These carburetors have all of the performance features of Edelbrock`s performer carburetors, with an added twist: the Qwick Tune secondary air valve. This air valve can be easily adjusted to kick in the secondaries early or late, no extra springs are needed. These CNC-profiled, ball-burnished aluminum carbs feature black accented hardware and GM/AMC...
This bell crank kit features 12 mounting holes for multi-arm positioning and can be used in either push or pull type throttle linkages. Center hole is ¼`` diameter for easy mounting. Each arm has 3 holes for various throttle ratios. Kit includes all hardware needed for installation along with universal throttle bracket.