MR. GASKET Vacuum Cap Assortment

MRG-3704
Use to block off open engine vacuum fittings. Sixteen pcs. Of "Buna-N" rubber offer more durability, longer life than neoprene/vinyl, especially when exposed to high temps.
16,85 CHF
inkl. MwSt.
Menge

  • Ihre Daten sind bei uns sicher und werden nicht an Dritte weitergegeben¨ Ihre Daten sind bei uns sicher und werden nicht an Dritte weitergegeben¨
  • Lieferungen gemäss den allgemeinen Geschäftsbedingungen Lieferungen gemäss den allgemeinen Geschäftsbedingungen
  • Umtausch gemäss den allgemeinen Geschäftsbedingung Umtausch gemäss den allgemeinen Geschäftsbedingung

Artikeldetails

MRG-3704

16 other products in the same category:

EDELBROCK Thunder Series Carburetor 650 cfm Manual Choke Endura Shine

These carburetors have all of the performance features of Edelbrock`s performer carburetors, with an added twist: the Qwick Tune secondary air valve. This air valve can be easily adjusted to kick in the secondaries early or late, no extra springs are needed. These CNC-profiled, ball-burnished aluminum carbs feature black accented hardware and GM/AMC...

Price CHF776.65
More
In stock

MR. GASKET Carburetor Studs Bullet Tip 1-1/2''

This is a high quality carburetor stud that looks good and works well in all applications. This stud has a bullet tip which allows for easy carburetor installation and eliminates that problem of carb getting hung on the threads and not going down straight to the intake.

Price CHF16.85
More
In stock

MR. GASKET Carburetor Studs 2-1/2''

Mr. Gasket medium length carburetor studs put an end to stripped-out threads in cast aluminum manifolds, holding the gasket in place and perfectly aligning the carburetor in position. Zinc-plated and 2.5-inch long, they have 5/16-18 threads on one end and 5/16-24 on the other, come in a package of four, and have four matching nuts and washers to complete...

Price CHF13.60
More
In stock

EDELBROCK 4-Barrel Carburetor Spacer

These Edelbrock carburetor spacers allow you to space your carburetor above the intake flange to increase plenum area for more torque and horsepower. Available in aluminum and heat-insulating phenolic or wood fiber, these Edelbrock carb spacers are just what you need to insulate or tune your carburetor/manifold powerband.

Price CHF55.70
More
In stock

EDELBROCK Metering Jets .116''

Are you using an Edelbrock Performer or Thunder series AVS carburetor? Then you need these Edelbrock metering jets! The jet and rod is changed to get the cruise air/ fuel ratio leaned out. The step in the rod changes the effective jet area between high and low manifold vacuum conditions. The brass metering jets are designed for use with Edelbrock...

Price CHF12.50
More
In stock

EDELBROCK Idle Mixture Screw Set

These Edelbrock carburetor idle mixture screws will fit directly into the base plate of your Edelbrock carburetor. They will allow adjustment to the idle circuit inside of the carburetor base plate. The screws are made of steel and include new springs for a simple installation.

Price CHF15.95
More
In stock

MR. GASKET Carburetor Studs 2''

Mr. Gasket medium length carburetor studs put an end to stripped-out threads in cast aluminum manifolds, holding the gasket in place and perfectly aligning the carburetor in position. Zinc-plated and 2-inch long, they have 5/16-18 threads on one end and 5/16-24 on the other, come in a package of four, and have four matching nuts and washers to complete...

Price CHF16.85
More
In stock

EDELBROCK Metering Jets .110''

Are you using an Edelbrock Performer or Thunder series AVS carburetor? Then you need these Edelbrock metering jets! The jet and rod is changed to get the cruise air/ fuel ratio leaned out. The step in the rod changes the effective jet area between high and low manifold vacuum conditions. The brass metering jets are designed for use with Edelbrock...

Price CHF12.50
More
In stock

EDELBROCK 4-Barrel Carburetor Spacer

These Edelbrock carburetor spacers allow you to space your carburetor above the intake flange to increase plenum area for more torque and horsepower. Available in aluminum and heat-insulating phenolic or wood fiber, these Edelbrock carb spacers are just what you need to insulate or tune your carburetor/manifold powerband.

Price CHF72.60
More
In stock

EDELBROCK 4-Barrel Carburetor Spacer

These Edelbrock carburetor spacers allow you to space your carburetor above the intake flange to increase plenum area for more torque and horsepower. Available in aluminum and heat-insulating phenolic or wood fiber, these Edelbrock carb spacers are just what you need to insulate or tune your carburetor/manifold powerband.

Price CHF61.95
More
In stock

MR. GASKET Carburetor Heat Dissipator

Special heat-absorbing material with layers of aluminum alloy forces heat away from the carburetor. Allows a cooler, denser fuel mixture to prevent engine heat from vapor-locking gasoline in the carburetor.

Price CHF61.85
More
In stock

EDELBROCK Accelerator Pump Assembly

When doing a rebuild on your Edelbrock carburetor, don`t forget to replace your accelerator pump with one of these top quality replacement pump assemblies. The right components will help to keep your carb working to its full potential.

Price CHF21.45
More
In stock